Worcester Si Mk II Bedienerhandbuch

DT10RF PROGRAMMERDIGISTAT - Radio frequency controlled programmable room thermostatwith domestic hot water programmerFOR GREENSTAR CDi, GREENSTAR i JU

PROGRAMMABLE SETTINGSADJUSTING TIMES & TEMPERATURES2. After 5 seconds the Digistat will start controlling at theselected set point but now display

ORORAuto mode indicator3. Press > once to confirm, the display will show temperatureflashing.4. Press + or - buttons to adjust temperature and pres

DIGISTATUSER OPTIONSOption Description of Option Min Max Default01 Change clock 12h/24h 12 24 2402 Change pre-set program 1 3 103 Change number of pro

DIGISTATUSER OPTIONSPre-set Program 3 (Home Worker) 24 hours As you can see, at 06:00, the heating will come on to raise thetemperature to 21°C.At 08

DIGISTATUSER OPTIONSDate and time setting.The DT10RF Programmer comes with a pre-set clock, which alsoautomatically adjusts for daylight saving time c

DIGISTATUSER OPTIONSOption selectTemperaturesettingNOTE: Option 5 must be completed or at least “steppedthrough” using the > key before option 6 c

DIGISTATUSER OPTIONSOption selectOn/OffsettingOption 09 How to lock the key pad - Access ProtectionLock.The access protection lock allows you to lock

DT10RF RECEIVEROPERATING CONTROLSMode indicatorHot water pre-heat ON lightHot water pre-heatselect button, movesthe mode indicator upand down to selec

Hot Water:1. Press select button to choose off = constantly OFFtimed = up to 3 ON and 3 OFF time periods asprogrammedonce = ON from first ON until

NOTE: The ON/OFF periods pre-programmed forHot Water pre-heat are shown in thetable opposite. The factory installed settings can be usedwithout any fu

8_716_115_493a 9/2/09 09:45 Page 2

SETTING MON - FRI1. Press set? until SET and PROG? are shownin the display. Press OK to select PROG tocontinue with programming.2. Press OK to select

Setting individual weekdays:NOTE: If you do not require individual weekdaytimes, then press set? until SET SAT-SUNis displayed and continue on the nex

DT10RF RECEIVERPROGRAMMABLE SETTINGSSetting SAT - SUN:1. Press OK to select weekend.NOTE: Speed up the display by holding down the + or - buttons.2. P

DT10RF RECEIVERPROGRAMMABLE SETTINGSSetting individual weekend days:NOTE: If you do not require individual weekendtimes, then press set? until the nor

Setting the clock and time1. Press the set? button until SET and CLOCK aredisplayed.2. Press OK. 3. Press + to switch between 24hr and 12hr display.4.

DT10RF RECEIVERPROGRAMMABLE SETTINGSSetting the dateNOTE: If the day displayed is incorrect, the dateneeds resetting as follows:1. Press the set? butt

DT10RF RECEIVERINSTALLATIONDANGER: 230 VOLTSDO NOT TOUCH THE ELECTRICAL COMPONENTSOR CIRCUITSCAUTION: ISOLATE THE MAINS ELECTRICITYSUPPLY BEFORE START

DIGISTATINSTALLATIONDIGISTAT / DT10RF RECEIVERSETTING UP THE RF LINKReceiver set up:After initial start up, the colon, CH and antenna symbols should b

DigistatDIGISTATINSTALLATIONDIGISTAT / DT10RF RECEIVERSETTING UP THE RF LINKSignal strength indicatorsTransmitter code(may be different)LED indicator

DIGISTATINSTALLATIONDIGISTAT / DT10RF RECEIVERMOUNTING THE DIGISTATPositioning RF room thermostatsThe Digistat is a radio frequency device which isver

WORCESTER, BOSCH GROUP:TECHNICAL 08705 266241SERVICE 08457 256206SPARES 01905 752571LITERATURE 01905 752556TRAINING 01905 752526SALES 01905 752640WEBS

DIGISTATINSTALLATIONDIGISTAT / DT10RF RECEIVERTO CHECK PREVIOUSLYINSTALLED UNIT 3. Replace the front cover by locating in position andpushing fully on

DIGISTATINSTALLATIONDIGISTAT / DT10RF RECEIVERTO CHECK PREVIOUSLYINSTALLED UNIT Signal strength indicatorsTransmitter code(may be different)LED indica

DIGISTATINSTALLER OPTIONSInstaller Options1. If you wish to change any of the Installer Options as shown in the table below, enter the InstallerOption

DIGISTATINSTALLER OPTIONSIf enabled, the start time should be set an hourearlier than the time you want the property to reachthe set temperature.Intel

DIGISTATBATTERY CHANGEInstallerOptionsFunction SelectOptionDefaultIf system protection is selected the system will beoperated for a period as shown in

Maintenance:The Transmitter (Digistat Programmer or OptimisingProgrammer) requires no maintenance.The outer casing can be wiped clean using a drycloth

Worcester, Bosch GroupCotswold Way, Warndon, Worcester WR4 9SW.Tel. 01905 754624 Fax. 01905 754619worcester-bosch.co.ukWorcester, Bosch Group is a bra

TECHNICAL DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . .

EC Directives:European Union Law Directive 2000/84/ECLow Voltage Directive (2006/95/EC)Electro-Magnetic Compatibility Directive (89/336/EEC)EC Marking

What is a programmable room thermostat?A programmable room thermostat is both a pro-grammer and a room thermostat. A programmerallows you to set ‘On’

GENERAL INFORMATIONOPERATING CONTROLSDigistat DaysTemperaturesee note+ or - buttons for setting adjustmentClock modeRight hand button > moves the p

DIGISTATPRE-PROGRAMMED SETTINGSThe Digistat ProgrammerThis is a 24-Hour programmable thermostat product (the same program for every day of theweek) w

Digistat Programmer - 24 hour operation1. With the product operating as normal in Auto mode press >twice until the time display is flashing as show